Lady’s Island Marina SC – Sailing into our next chapter

The End of a Chapter – Summer 2024

We had been discussing selling Cerca Trova and moving back to land for about six months. I was getting tired of constantly repairing the boat and Lynette’s knees were continuing to bother her more and more. After the long winter trying to get to the Bahamas hampered by either boat repairs or weather issues, we decided it was time for a change.

We had three and a half good years of sailing on two different boats and traveled almost 8,500 nautical miles during that time. We saw some very cool places and met many great people along the way. I wouldn’t give up those years for anything. This sailing adventure was a bucket list item for me, and I was able to check it off my list. Possibly the only regret I have is that we didn’t make it to the East Caribbean on our own sailboat.

With me at almost 72 and Lynette at closing in on 69, I was tired and neither of us had the energy to keep going. Are there other cruisers older than us? Certainly, but most cruisers we met were younger than us and many were way younger. This makes me wish we had cast off years earlier, but that just wasn’t in the cards.

We left off in our last post arriving at Lake Worth, FL, in the evening of May 17, 2024. We spent some time with our friends, Josh and Sheila, who were anchored there and met up with some old friends we had met in San Diego, Dave and Mary on Yo-D-Yo. All six of us had met back in San Diego in 2021 and had stayed in touch. This was the first time we had all been together since 2021 in San Diego. It was a great reunion and hopefully not to be the last.

We departed Lake Worth with Yo-D-Yo on May 20^st at 7:00 am, heading north. The weather was good, so we opted to go outside instead of up the Intracoastal Waterway (ICW). We motored but tried multiple times to sail with not much luck, as the wind was just too far forward to make any headway. We arrived at Ft Pierce Inlet with the tide coming in, so got a nice push to our anchorage from the current. We made 9 knots speed over ground (SOG), which is fast for Cerca Trova. We anchored on the south side of the channel almost to the ICW at 4:16 pm and then went out to dinner with Yo-D-Yo and another couple they knew.

We weighed anchor the next morning at 8:48 am, heading north up the ICW. This was an easy and uneventful passage to our next stop at an anchorage near Paradise Blvd. in Melbourne, FL. We arrived at 5:24 pm and settled in for the night. The day had been sunny and warm, and we were happy to be on track, moving north.

There is a free dock at Cocoa Village, FL, that we planned as a stop. This was a very short 15nm passage, so we leisurely left our anchorage at 10:05 am on May 22^nd and motored up the ICW to Cocoa Village. We docked at 1:03 pm after asking another boat on the dock if they would move a bit so we had room to dock.

Arriving early gave us plenty of time to explore the town of Cocoa Village and get some much-needed walking exercise. Cocoa Village is a quaint town with lots to offer. We explored a great old hardware store and ate ice cream at a cute ice cream parlor. That evening we walked back into town and had a fantastic dinner with the Yo-D-Yo crew, Dave and Mary.

Next stop, Titusville Marina. Titusville Marina had been our first marina upon arriving back in the US on or previous boat, No Regrets, and our third visit there in total. We arrived on May 23^rd at 1:07 pm after a short 18nm motor up the ICW. We knew the town well, so walked to dinner with Dave and Mary, and stocked up on groceries. We bid Dave and Mary goodbye after a couple of days as they headed to Brunswick, GA.

During our stay in Titusville, we made plans to haul out and have some saildrive work done. Our port saildrive had a loose zinc anode that I had noticed while diving and cleaning the bottom in the Bahamas. I was unable to tighten it then, so figured the only way was to haul the boat out and address it on the hard. We made arrangements at Sea Love Boat Works at Ponce Inlet, FL, to haul out on May 28^th, so left Titusville in the morning of May 27^th. The passage was 35nm and took us most of the day, arriving around 4:45 pm. The next day at slack tide Cerca Trova was in the sling and on its way out of the water.

We rented a small AirBnB condo in South Daytona Beach for 9 days while Cerca Trova was in the yard. It was on a bus route that had a stop very close to the boatyard, so I took the bus to and from the boatyard every day to work on the boat. As I was dismantling the zinc anode on the port saildrive, I found that the mounting holes had corroded to the point where they would no longer hold the zinc in place, so I had to order a replacement end cap and wait for it to arrive. In the meantime, I had the yard sand off the copper-based bottom paint from both saildrives and apply a non-copper-based bottom paint. I removed the propellers, sanded them, and applied a prop antifouling paint. Then I tacked polishing and waxing the underside of the bridgedeck and waterline along the hulls. That was a big job, holding the buffer over my head for multiple days. I certainly had a great workout, and probably overdid it.

While we were at the AirBnB, the older couple who owned the condo were very interested in our sailing adventures, so they offered to take us to dinner. We had a wonderful time walking along the beach with them and talking about our sailing adventures. They were very nice, and we enjoyed the short time we spent with them.

With the boat work done, we splashed on June 4^th, 2024, and tied up to the dock next to the boatyard. We headed north the next morning at 7:00 am along the ICW. I noticed some gray smoke from the port engine and the coolant temperature was a bit high, so kept my eye on it. Always something to cause concern on a boat. The port engine continued to heat up, so we switched to the stbd engine to let it cool down. We arrived at the mooring field in St Augustine at 3:45 pm after an almost uneventful passage of 55nm.

Since the mooring field was very close to the ocean inlet, we had quite a current shift as the tides changed. With the wind blowing in one direction and the current running in the other, the boat was fighting to stay in one place on the mooring ball. Several times the ball was pulled under one hull or the other as the boat shifted to the wind and current. After one night of this, and it was constant, we decided to get a slip at the dock for the remainder of our stay.

St Augustine claims to be the oldest city in the US with fantastic Spanish colonial architecture. We took an Uber into town to see some of the sights the city is famous for. It was good to get out and walk around. We certainly needed the exercise.

The weather was good, so on June 8^th, 2024, we decided to do an over night from St Augustine to Lady’s Island Marina in Beaufort, SC. This was an outside passage as the ICW through Georgia is long and winding, and quite frankly, a bit boring. So, to keep us on our toes, we decided on short and quick. Well, not so quick as it was a 162nm passage. We motored the entire way as the wind was on our nose and light, as was often the case.

We arrived at Lady’s Island Marina on June 9^th, 2024, at 3:45 pm, and checked in with the marina. Our tasks now were to prepare Cerca Trova for sale and make plans to find a place to live. This was our last official passage on Cerca Trova. We came full circle as Lady’s Island Marina is where we saw Cerca Trova for the first time back in 2022 while looking for a new sailboat. Sometimes things do go full circle, and this was one of them.

We spent quite a bit of time cleaning Cerca Trova and taking pictures for the boat listing. Once she was listed, we had several showings and then one couple decided they wanted her. I was very grateful she sold quickly and just like that; this chapter was closed.

We are now back on land and happily living near Greenville, South Carolina. We found a small house that we are quickly turning into a home. We had no furniture, so that was first on the list, and are now getting landscaping done and planning a summer garden. Welcome to our new next chapter.

Beaufort, SC to New Bern, NC – Summer 2023

Lady’s Island Marina in Beaufort, SC is where Cerca Trova summered before our ownership, and the previous owners had a reservation for 2023 that we took over. We decided to stay at Lady’s Island Marina for a month to do some repairs and settle in for a bit. It was nice to have a little stability for a change. Constantly moving on almost a daily basis can take its toll.

The marina has an old pickup truck they lend to their slip customers for an hour at a time. Frankly, one hour is not enough time to go grocery shopping, but they were firm on the time. We just never got the truck back within an hour. It was usually an hour and a half, but they never complained.

Many packages were waiting for me when we got to the marina, so I got busy with the repairs the next day. The list was quite long:

Replace the freezer compressor fan with a more powerful one to help with cooling
Replace the burned-out starboard engine blower
Replace the Furuno PG700 heading sensor (electrical storm damage)
Replace the Furuno IF-NMEAFI analog to NMEA2000 converter (electrical storm damage)
Replace the poorly crimped butt connector between the alternator and the Sterling Alternator Protection Device
Remove the dead Volvo Penta MDI (Mechanical Diesel Interface) black box on starboard engine and test the Multilink cable for continuity
Change all watermaker filters and clean the strainer
Replace starboard engine tachometer with a rebuilt one
Add 5″ duct from refrigerator/freezer compressor fan to washer/dryer locker
Replace defective inlet pressure transducer on watermaker
Replace the dead MDI box on starboard engine with a new one
Add stainless screens to the four engine vents and the galley stove vent to prevent bugs and other critters from entering the boat
Have someone climb the mast to install a new wind transducer (electrical storm damage) and remove the TV antenna
Rewire the entire NMEA2000 electronics network properly
Replace the empty propane tank with a full one
Replace copper ground foil for SSB radio
Replace wrong size hose clamp on the water inlet to the aft washdown hose to stop it from leaking
Update firmware on the Furuno MFD and other Furuno devices
Replace the broken cockpit hatch
Replace galley stove igniter battery and battery holder
Add King Starboard rails to slide stove in and out more easily
Replace cockpit speaker wires
Replace saloon speaker wires
Replace cockpit speakers
Replace gypsy, two cone clutches and two seals on windlass
Replace stereo and clean up wiring in TV/Stereo cabinet
Have dealer replace screen in screen door
Have a diver clean the bottom and replace the port saildrive zinc screw
Polish vinyl windows in cockpit
Rebed port forward saloon window top to prevent leaks

And after thousands of dollars and lots of hard work, the list was completed, for now. In addition to the boat projects, we got our eyes examined, purchased new glasses, and went to the dentist to get our teeth cleaned and checked. I’m proud of what we were able to accomplish in only one month. We were both exhausted and ready to stop working and move on.

When I was cleaning the ICW mustache – what locals call the brown scum that collects on the hull after traveling on the ICW – I saw black soot on each hull around the engine exhaust ports, so after a little Google research, I found I needed to get the diesel engine injectors cleaned, as they had never been cleaned in over 2,000 hours of use. I didn’t feel I knew enough about the Volvo Penta engines, so I scheduled a qualified company to remove the injectors and have them tested. This was to be done in Charleston, SC, so I made an appointment and off we went.

*Moonrise at White Point Landing anchorage*

We Left Lady’s Island Marina at 9:30 am on Lynette’s birthday, August 1^st. We didn’t want to push it, so we dropped anchor at 4:50 pm at White Point Landing. This was a little sporty anchorage but not too bad. We knew that the tides have a range of about 8′ in this area, so we anchored in about 15′ of water as it was high tide when we arrived, and didn’t want to ground at low tide.

The next day we weighed anchor at 9:45 am and went the 24nm to Charleston. The Safe Harbor Charleston Marina put us on the outside dock, which was not protected at all. I called the office and they said when we got fuel, they would move us to the inside of that dock. We were both a bit tired, so we waited until the next day to get fuel and move the boat to the other side of the dock. All went well and that side of the dock was much quieter. I’m glad I asked to be moved. It never hurts to ask, right?

It took several days for the Volvo mechanic to schedule us to remove the injectors. When he arrived, he had a trainee in tow, so each worked on an engine. We found out the hard way that the fuel return lines from both engines didn’t dump into the top of the tank, but rather had a tube that went to the bottom (I’m assuming) of the tank. This set up a siphon that drained fuel into the bilge. There was no valve in the return lines to shut off the flow, so the mechanics put a bolt in each line with a hose clamp. That seemed to stop the flow. They took the injectors and left for their shop.

We woke up the next morning with the port bilge full of diesel, almost to the top. I texted the mechanics and they came quickly to deal with the issue. They brought a pump and pumped out over 10 gallons of diesel from that bilge into 5-gallon buckets that we filtered back into the boat tank using our Baha Filter. The mechanics then fabricated a better solution to stop the diesel from leaking. What a mess to clean up. I spent all that day scrubbing the bilge with bilge cleaner and dealing with the dirty liquid. Not fun and the boat smelled so bad that we had headaches from the diesel fumes for days.

The Volvo shop person called and said that the injectors were in bad shape and needed to be replaced. Volvo distribution had no injectors for our engines in the US, of course, but they did have spare parts, so the Volvo shop rebuilt the injectors. A few days later, one of the mechanics came back to install them. All ran fine and I haven’t had any soot buildup on the hulls since then. Next time I will do the job myself and save a ton of money.

While we were in Charleston I noticed a leak in the starboard head cabinet under the sink, so while investigating where the leak was coming from the thru-hull drain fitting for the air conditioner cooling water broke and started flooding the area with salt water. I figured out it was the air conditioner cooling water and turned off the AC unit to stop the flow of saltwater into the boat. I now had a new issue to fix, on top of finding where the original water leak was coming from inside that cabinet. Ah, boat life. Never a dull moment.

To replace the thru-hull fitting required going under the bridge deck between the two hulls. There is only about 15” of space between the bridge deck and the water where the thru-hull fittings are located. My neighbor graciously loaned me his kayak so I could float under the boat. I could barely fit under the bridge deck to replace the thru-hull fitting, but I was able to get it done and reattach the drain hose. One issue was fixed.

While I was borrowing the dinghy, the owner of the boat behind us asked if I could help him from the water to tie straps around his dinghy. I obliged and he offered to take us to Whole Foods, Ace Hardware, and a liquor store for supplies a few days later. Very nice.

The original leak I was looking for wound up being a broken 3-way valve, used to change from fresh to salt water for the toilet. It was broken and every time water was turned on somewhere in the boat, it gushed out of the valve. Luckily, there was a spare onboard, so it was easy to replace. It’s all fixed for now.

The Safe Harbor Charleston City Marina is right near downtown, and the marina has a free shuttle that takes people to and from the farmers market, grocery stores, and West Marine. We took advantage of the shuttle and went to the farmers market to explore. It made for a nice day away from the boat and boat projects. Sometimes you need to take a break from the daily grind.

The highlight for us was that friends came to visit for a day, providing a chance to catch up on our lives and show them Cerca Trova. We topped off the visit with a very nice dinner and beers at a local brewpub.

We left Charleston on the morning of August 12^th heading to Santee Bay. We passed through some very skinny water, less than 5’ in some places. Our depth alarm sure let us know and so did the bottom a few times. Luckily it was only sand and mud. Along the way, we passed the dredge that was working its way down the ICW, deepening the channel. What a very slow process. They run 24 hours a day and move very slowly. It was a tight squeeze between the dredge and shallow water, but we made it past the dredge without incident.

We were able to take advantage of a weather window and went outside the ICW for a portion of our trek to New Bern, NC. The window provided a brisk broad reach from Little River, on the border of North and South Carolina, to Cape Fear, NC. After three anchorages since leaving Charleston, we were out in the ocean sailing for the first time in what seemed like forever. It was a brisk sail with a double-reefed main and full jib. Our top speed in about 18 knots of wind was almost 8.5 knots. It was nice to get the sails up and enjoy the ride.

Our anchorage for that night was at Carolina Beach, NC on the ICW. This was a cozy little anchorage off the ICW near some docks and homes along the banks. After the brisk day of sailing, it was nice to have a very quiet place to sleep.

We stopped at two more anchorages before reaching New Bern, NC. Along this route, the ICW goes through Camp Lejeune where the Marines often practice with live ammunition. By reading the notes on our digital charts I learned that the ICW is often closed in this area due to these live ammo practices. The notes had a phone number, so I called it to see if the ICW would be closed when we planned to pass through. There were no activities planned for the day, so we were clear to pass through Camp Lejeune uninterrupted. It pays to read the chart notes and comments from other mariners. They can be helpful.

We arrived at New Bern Grand Marina on August 18^th around 2:45 pm after fueling up at another marina nearby. We were on the outside of a breakwater dock and when the winds came from the East, it got a little rough. There was no other dock space available, so we had to live with the situation. Luckily it didn’t blow from the East all that often. We planned to be here for about a month and then head north to the Chesapeake Bay to explore the area.

Next time; enjoying New Bern, changing plans, more projects, and weather issues.